Malaysia Updates SRD Specifications for 2026

The Malaysian Communications and Multimedia Commission (MCMC) has introduced significant updates to its regulatory framework for wireless and communications equipment through the registration of two new technical codes effective 5 May 2026: MCMC MTSFB TC T022:2026, Communications Equipment – Baseline Requirements, and MCMC MTSFB TC T007:2026, Short Range Devices (SRD) – Specifications (Third Revision). These publications establish updated requirements for communications equipment and short-range devices seeking market access in Malaysia.

For manufacturers, test laboratories, and compliance professionals, the new Malaysia SRD Specifications represent an important revision affecting device categories, frequency allocations, power limits, operational conditions, and technical compliance obligations.

Malaysia SRD Specifications Introduce New Baseline Requirements

A key change introduced by the new framework is the creation of MCMC MTSFB TC T022:2026, which establishes baseline requirements applicable to communications equipment across Malaysia.

The technical code applies to communications equipment including user equipment, network facilities, and radiocommunications devices. It introduces harmonized requirements covering:

• Equipment marking and labeling
• Interoperability requirements
• IPv6 compliance
• Electromagnetic Compatibility (EMC)
• Electrical safety
• Specific Absorption Rate (SAR)
• Power Density (PD) assessments

Additionally, communications equipment supporting IP-based functionality must comply with IPv6 requirements, while applicable products must demonstrate compliance with EMC, electrical safety, SAR, and power density standards.

Key Changes in the Revised SRD Technical Code

The revised MCMC MTSFB TC T007:2026 defines technical requirements for a broad range of short-range devices, including:

• RFID equipment
• Wireless microphones
• Security devices
• Industrial, Scientific and Medical (ISM) equipment
• Ultra-Wideband (UWB) devices
• Medical implant devices
• CCTV access systems
• Automotive radar sensors
• Radio Local Area Network (RLAN) equipment

Moreover, the revised code establishes updated operating frequencies, output power limits, spurious emission requirements, and applicable test standards.

New Device Categories and Frequency Allocations

Several notable additions and revisions have been incorporated into the 2026 version.

Security devices are now explicitly authorized within the 303–320 MHz frequency band.

For ISM equipment operating in the 13.553–13.567 MHz band, the code establishes a dedicated 500 mW EIRP category.

Additionally, a new Narrowband Device category has been introduced within the 5.925–6.425 GHz range. The new allocation permits operation at 25 mW EIRP for indoor and outdoor applications intended for short-range communications.

For Active Medical Implant Devices operating in the 405–406 MHz band, the code establishes specific operational conditions. Devices implementing Adaptive Frequency Agility (AFA) and Listen Before Talk (LBT) mechanisms may operate at 25 μW ERP, while Low Power Low Duty Cycle (LPLDC) devices remain subject to lower thresholds.

Updated Operational Restrictions

The revised framework also introduces important operational limitations intended to protect spectrum integrity.

Short Range Communication (SRC) devices are excluded from operation in the 87.5–108 MHz band.

Furthermore, RFID operations are consolidated within the 919–923 MHz frequency range, eliminating the previous allocation in the 923–924 MHz band.

Wireless microphones operating within 87.5–108 MHz are now regulated using Effective Radiated Power (ERP) measurements rather than Effective Isotropic Radiated Power (EIRP).

However, one of the most significant restrictions applies to the 5.25–5.35 GHz band. Devices operating within this frequency range are restricted to indoor use inside buildings only. Installation in road vehicles, trains, and aircraft is explicitly prohibited.

Impact on 6 GHz RLAN Devices

The revised code also formalizes requirements for 6 GHz operations.

RLAN and narrowband devices operating between 5.925 GHz and 6.425 GHz may operate at:

• 25 mW EIRP for indoor and outdoor short-range applications
• 250 mW EIRP for indoor deployments intended for permanent installation in buildings, aircraft, or trains

These provisions align with the growing adoption of next-generation wireless technologies utilizing the 6 GHz spectrum.

How Entirety Can Help

Organizations managing wireless products across multiple jurisdictions should continuously monitor evolving spectrum and technical requirements. Entirety’s Regulatory Intelligence services help manufacturers stay informed about regulatory developments affecting wireless technologies, spectrum allocations, and market access requirements worldwide.

Learn more:
https://entirety.biz/services/regulatoryintelligence/

Impact Assessment

Technical Standards?  Yes

Type Approval & Market Access?  Yes

Imports, Customs, Trade, or Market Surveillance?  No

Spectrum Management?  Yes